So, at weatherly the car was running great, right up until I broke the crap out of the driver side inner driver/tripod bearing, ended up looking like this:
Fixed it saturday night, and on the first dry run on sunday, on the same turn, it did the same thing
So i figured it was probably the horrible old stock 99 motor mounts, but i just replaced those with some hockey pucks, and did a test fit of the axle without an inner boot, and with the suspension loaded (seemingly the middle of the travel is when the axle is farthest out?) the tripod is probably 1/4 of the way outside of the inner driver cup, whereas the passenger side is solidly inside the cup at that point.
So what I'm trying to figure out is, what am I doing wrong? So we're all on the same page, this is a 99 with a 16v, but on the stock 99 mounts, so the trans should be in the same place as a normal 99. I'm running the smaller inner drivers, and the axles from the 99, along with 87 vented rotor hubs with the appropriate outer cv joints and the axle shafts that came in the car. The easy thing would be to line up a bunch of early shafts and see if I can find a different one, but unfortunately we really don't have any spare axle shafts on hand except in cars, and I don't feel like randomly taking them apart to check lengths.
Paul
Axle issues.
- squaab99t
- Posts: 1268
- Joined: Wed Mar 28, 2007 5:43 pm
- Number of Saabs currently owned: 4
- Location: Shoreline Wa
Re: Axle issues.
Duplicate post
Last edited by squaab99t on Thu Sep 25, 2014 8:24 am, edited 1 time in total.
- squaab99t
- Posts: 1268
- Joined: Wed Mar 28, 2007 5:43 pm
- Number of Saabs currently owned: 4
- Location: Shoreline Wa
Re: Axle issues.
Quaife limited slip diff? Did you put in the dual plungers on the inner drivers?
- SwedeSport
- Posts: 3021
- Joined: Mon Jun 15, 2009 9:52 am
- Number of Saabs currently owned: 5
- Location: Pottstown, PA
- Contact:
Re: Axle issues.
I think you need to find the axles off the later vented brake 900s. The axles are longer than their earlier counterparts. The 87 vented brake hubs have a different offset, and require a different axle.
IIRC, that car was wrecked pretty hard at one (or more than one) point in time. It could be possible that somehow the engine shifted to one side or the body shifted away from the engine, and was not properly straightened????
Attached is a snapshot of the blurb from the Bentley Manual about the axles.
IIRC, that car was wrecked pretty hard at one (or more than one) point in time. It could be possible that somehow the engine shifted to one side or the body shifted away from the engine, and was not properly straightened????
Attached is a snapshot of the blurb from the Bentley Manual about the axles.
Swedesport Motors, Apparel and Accessories for SAAB Junkies.
Http://Facebook.com/swedesportmotors
Swedesportmotors@gmail.com
Http://Facebook.com/swedesportmotors
Swedesportmotors@gmail.com
- Jordan
- Site Admin
- Posts: 4068
- Joined: Fri Oct 13, 2006 2:38 pm
- Number of Saabs currently owned: 6
- Location: Vernon, CT
- Contact:
Re: Axle issues.
If you post up an axle length measurement I can cross with a few others.
-
- Posts: 607
- Joined: Wed Mar 21, 2007 10:09 pm
- Number of Saabs currently owned: 2
- Location: Reading, PA
- Contact:
Re: Axle issues.
I'll have to pop the outer CV out and measure it, unless you want the whole axle measurement? I'm presuming if I used a later axle I'd have to swap to the later inner drivers too, right? Guess theres no reason not to at this point, but I'm getting tired of swapping that damn thing, have to jack the motor up to do it in a 99. Squaab, the car has a gripper, and has both plungers like it's supposed to.
Paul
Paul
- SwedeSport
- Posts: 3021
- Joined: Mon Jun 15, 2009 9:52 am
- Number of Saabs currently owned: 5
- Location: Pottstown, PA
- Contact:
Re: Axle issues.
in order to measure the axle, you have to take the tripod, and the outer out...
I believe you can also measure the difference at the recess where the boot clamp rides, but it wont be as accurate.
I believe you can also measure the difference at the recess where the boot clamp rides, but it wont be as accurate.
Swedesport Motors, Apparel and Accessories for SAAB Junkies.
Http://Facebook.com/swedesportmotors
Swedesportmotors@gmail.com
Http://Facebook.com/swedesportmotors
Swedesportmotors@gmail.com
Return to “SAAB MOTORSPORT TECH”
Who is online
Users browsing this forum: No registered users and 2 guests