Rebuilding hydraulic lifters

THE place for technical discussions concering the construction and preparation of SAABs for all forms of motorsport, Rally, Road Racing, Auto-X etc....
User avatar
Jon1
Posts: 278
Joined: Sat Mar 01, 2008 5:09 pm
Number of Saabs currently owned: 30
Location: Fort Edward, NY
Contact:

Rebuilding hydraulic lifters

Postby Jon1 » Sat Jan 14, 2017 10:33 am

Has anyone here had any experience rebuilding hydraulic lifters? I don't know the history on any of the engines that came in my cars and they are 25 to 30 years old. I watched this video and I think I will attempt to disassemble and clean some lifters. https://www.youtube.com/watch?v=ySf0r8GGMOY Another video https://www.youtube.com/watch?v=zu60ExxQjlg
Jon
jon1
with many classic 900 turbos

User avatar
squaab99t
Posts: 1262
Joined: Wed Mar 28, 2007 5:43 pm
Number of Saabs currently owned: 4
Location: Shoreline Wa

Re: Rebuilding hydraulic lifters

Postby squaab99t » Sun Jan 15, 2017 10:20 am

I have only went as far popping out the piston assembly and putting that in an ultrasonic bath. To be honest, I have only cleaned them, coated them with oil, and sitting in a bag.
That is a great vid on complete disassembly and reassembly. Even the same manufacturer IND.

User avatar
Jon1
Posts: 278
Joined: Sat Mar 01, 2008 5:09 pm
Number of Saabs currently owned: 30
Location: Fort Edward, NY
Contact:

Re: Rebuilding hydraulic lifters

Postby Jon1 » Sun Jan 15, 2017 4:28 pm

I popped out the piston assembly, but could not get them any farther apart. I cleaned them in kerosene, pushing the check ball in and out to release the dirty oil. I cleaned them multiple times and then lubed them with oil, making sure they weren't full of oil before reassembly. Five out of the sixteen were very gummed-up before cleaning. I am glad I took the time to clean them.
Jon

jon1

with many classic 900 turbos

User avatar
Jon1
Posts: 278
Joined: Sat Mar 01, 2008 5:09 pm
Number of Saabs currently owned: 30
Location: Fort Edward, NY
Contact:

Re: Rebuilding hydraulic lifters

Postby Jon1 » Sun Jan 15, 2017 4:33 pm

I installed new valve seals Image

Image

Installed the valves
Image

...springs and keepers

Image

Image
Last edited by Jon1 on Sun Jan 15, 2017 4:43 pm, edited 1 time in total.
Jon

jon1

with many classic 900 turbos

User avatar
Jon1
Posts: 278
Joined: Sat Mar 01, 2008 5:09 pm
Number of Saabs currently owned: 30
Location: Fort Edward, NY
Contact:

Re: Rebuilding hydraulic lifters

Postby Jon1 » Sun Jan 15, 2017 4:36 pm

It hurt my hand to slam the lifters like in the video, so I made a tool to knock them apart Image

Image
Jon

jon1

with many classic 900 turbos

User avatar
Jon1
Posts: 278
Joined: Sat Mar 01, 2008 5:09 pm
Number of Saabs currently owned: 30
Location: Fort Edward, NY
Contact:

Re: Rebuilding hydraulic lifters

Postby Jon1 » Sun Jan 15, 2017 4:41 pm

See how dirty the kerosene got, it had a lot of sediment in it when I dumped it out. (Old head that I took the cams and lifters from on the right:

Image

Image

T5 head that the cams and lifters went into

Image

Image
Jon

jon1

with many classic 900 turbos

User avatar
squaab99t
Posts: 1262
Joined: Wed Mar 28, 2007 5:43 pm
Number of Saabs currently owned: 4
Location: Shoreline Wa

Re: Rebuilding hydraulic lifters

Postby squaab99t » Mon Jan 16, 2017 12:34 am

Jon1 wrote:It hurt my hand to slam the lifters like in the video, so I made a tool to knock them apart


I remember my hand smarting pretty good on that maneuver. Good looking tooling. Tools, separates us from animals...

gmreider
Posts: 326
Joined: Fri Jul 13, 2012 8:28 am
Number of Saabs currently owned: 6
Location: Boyertown PA

Re: Rebuilding hydraulic lifters

Postby gmreider » Mon Jan 16, 2017 12:00 pm

Jon, Interesting Stuff. I am going out and start banging my lifters on a board.
I like your tooling also. When I get some time I will send photos of my tooling for head work for your review. I do some things a bit different, but you may find them useful.

DeLorean
Posts: 1193
Joined: Sat Mar 31, 2007 9:54 pm
Number of Saabs currently owned: 9
Location: Pennsylvania, Forever!
Contact:

Re: Rebuilding hydraulic lifters

Postby DeLorean » Wed Jan 18, 2017 8:19 am

Gary has head work down to a production line science. I think it took us about 1/2 an hour to do the valve seals & Volvo 240 valve spring upgrade in my T5 head for the hillclimb car.
Less brake more gas!

User avatar
Jon1
Posts: 278
Joined: Sat Mar 01, 2008 5:09 pm
Number of Saabs currently owned: 30
Location: Fort Edward, NY
Contact:

Re: Rebuilding hydraulic lifters

Postby Jon1 » Thu Jan 19, 2017 9:30 am

I am almost embarrassed to say, these are the first heads that I have ever taken apart and reassembled. I have never had a need to do so before. I look forward to seeing Gary's procedure.
Jon

jon1

with many classic 900 turbos

Nate
Posts: 132
Joined: Fri Jul 13, 2007 9:57 pm
Number of Saabs currently owned: 1

Re: Rebuilding hydraulic lifters

Postby Nate » Tue Mar 21, 2017 8:50 am

How hard did you have to "slam" the lifter? I copied your tool design and slammed the lifter against a piece of pine & just ended up nicking the lifter's edge. Seems counter-intuitive to hit the lifter to pop the piston out when it should pull out. I don't know how to grab on to it without mangling up the piston though.

User avatar
Jon1
Posts: 278
Joined: Sat Mar 01, 2008 5:09 pm
Number of Saabs currently owned: 30
Location: Fort Edward, NY
Contact:

Re: Rebuilding hydraulic lifters

Postby Jon1 » Tue Mar 21, 2017 11:45 am

I made the tool so the lifter is a tight fit, so it won't fall out. Some of them came out with only one or two hits, a few took three or more hits. It takes quite a lot of force to get them to come out.
Jon

jon1

with many classic 900 turbos

User avatar
Geoff
Team Turbo Troll Crew
Posts: 3888
Joined: Fri Oct 20, 2006 3:31 pm
Nickname: Geoff
Number of Saabs currently owned: 6
Location: Nude Humpshire

Re: Rebuilding hydraulic lifters

Postby Geoff » Tue Mar 21, 2017 4:16 pm

Jon, thanks for sharing this. It's pretty cool to see that they can be popped apart and cleaned.

We have one of these at work, maybe this would get them apart?
https://www.youtube.com/watch?v=kDs6jQmNEdM
The kind of dirty that doesn't wash off :eyebrows:

gmreider
Posts: 326
Joined: Fri Jul 13, 2012 8:28 am
Number of Saabs currently owned: 6
Location: Boyertown PA

Re: Rebuilding hydraulic lifters

Postby gmreider » Thu Mar 23, 2017 10:31 pm

OK Jon, here are my methods and tricks for head work.
(1) I use a head holder stand as shown in photo, It allows me to swivel it all around and work from all sides and stand comfortably.
(2) I use a clamp type spring compressor with an old factory tool to compress the springs. Note I use a blue sleeve to protect the lifter bore as I work on each cylinder. Once you get used to the C clamp setup, it is quick.
(3) I show a home made valve seal installer. I oil up the vale stem and insert valve, oil the seal and slide it over the valve and then tap the seal in place. So the tool is guided by the valve stem.
(4) then I toss the spring and retainer in and use the C clamp. look at the neat magnetic keeper holder in the photos. I enter the tool straight down thru the top of the spring compressor and give a squeeze on the keeper tool to set the keeper and release the C clamp with the other hand. the C clamp tool is made to release with one hand and the keeper tool just slide off and the job is done.
I am sure there are small details that I have not mentioned, but this will get you thinking. I can strip a head for valve work in 1/2 hour or maybe less, and can lap in valves, install valves and seals, springs and lifters and cams in an hour and 1/2 or maybe less.
I notice that I show a pliers that is for removing the seals. It works great and is a available. The keeper tool , I have had for years , but I see similar versions for sale. These gadgets make the job nicer and quicker.

Next up when I get time is my take on installing the Quaife in C900 and the methods that I have used. That is when I get time. Enjoy>
Attachments
0322171759a_resized.jpg
0323171758_resized.jpg
0322171754_resized.jpg
0322171758_resized.jpg
0322171751_resized.jpg
Last edited by gmreider on Fri Mar 24, 2017 12:33 pm, edited 1 time in total.

User avatar
Jon1
Posts: 278
Joined: Sat Mar 01, 2008 5:09 pm
Number of Saabs currently owned: 30
Location: Fort Edward, NY
Contact:

Re: Rebuilding hydraulic lifters

Postby Jon1 » Fri Mar 24, 2017 5:28 am

Gary, that is a nice set-up! Thanks for sharing.
Jon

jon1

with many classic 900 turbos


Return to “SAAB MOTORSPORT TECH”

Who is online

Users browsing this forum: No registered users and 3 guests